21.5 Inch Best Quality PC Computer Monitor OEM Factory Supply 60Hz Desktop Monitor
Warranty and Components
1 Year Free Warranty for Monitor and all components.
USB Cable 180cm*1 Pcs,
VGA Cable 180cm*1 Pcs,
Power Cord with Switching Adapter *1 Pcs,
Open frame touch monitor paramters
General
|
Model
|
CDT215-CDK02
|
Series
|
Water-proof and Open frame
|
LCD Type
|
21.5
"
Active matrix TFT-LCD
|
Video Input
|
VGA, HDMI
|
OSD controls
|
Allow on-screen adjustments of Brightness, Contrast Ratio, Auto-adjust, Phase, Clock, H/V Location, Languages, Function, Reset
|
Power Supply
|
Type: External brick
Input (line) voltage
: 100-240 VAC, 50-60 Hz
Output voltage/current: 12 volts at 4 amps max
|
Mount Interface
|
-
VESA 75mm and 75mm
-
Mount with base
|
LCD Specification (Please refer to this model--NV156FHM-N46)
|
Active Area(mm)
|
344.16(H)×193.59(V) mm
|
Resolution
|
1920(RGB)×1080 FHD
141PPI
|
Dot Pitch(mm)
|
0.05975×0.17925 (H×V)
|
Nominal Input Voltage VDD
|
+3.3V
(Typ)
|
Viewing angle (v/h)
|
85/85/85/85 (Typ.)(CR≥10)
|
Contrast
|
800:1 (Typ.)
|
Luminance(cd/m2)
|
265 cd/m² (Typ.)
|
Response Time(Rising)
|
30 (Typ.)(Tr+Td) ms
|
Support Color
|
16.7M
|
Backlight MTBF(hr)
|
50000
|
Touchscreen Specification
|
Type
|
Projected Capacitive touch screen
|
Multi touch
|
10 points touch
|
Touch Life Cycle
|
10 millions
|
Touch Response time
|
8ms
|
Touch System Interface
|
USB interface
|
Power consumption
|
+5V@80mA
|
External AC Power Adapter
|
Output
|
DC 12V /4A
|
Input
|
100-240 VAC, 50-60 Hz
|
MTBF
|
50000 hrs
at 25°C
|
Environment
|
Operating Temp.
|
0~50°C
|
Storage Temp.
|
-20~60°C
|
Operating RH:
|
20%~80%
|
Storage RH:
|
10%~90%
|
Safety Instructions
-
Read these safety instructions carefully.
-
Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning.
-
For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.
-
Keep this equipment away from humidity.
-
Put this equipment on a reliable surface during installation. Dropping it or letting if fall may cause damage.
-
The openings on the enclosure are for air convection. Protect the equipment from overheating. DO NOT COVER THE OPENINGS.
-
Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.
-
Position the power cord so that people cannot step on it . Do not place anything over the power cord.
-
All cautions and warnings on the equipment should be noted.
-
If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient over voltage.
-
Never pour any liquid into an opening. This may cause fire or electrical shock.
-
Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.
-
If one of the following situations arises, get the equipment checked by service personnel:
-
The power cord or plug is damaged.
-
Liquid has penetrated into the equipment.
-
The equipment has been exposed to moisture.
-
The equipment does not work well, or you cannot get it to work according to the user's Manuel.
-
The equipment has been dropped and damaged.
-
The equipment has obvious signs of breakage.
14. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -1
0ºC OR ABOVE
50ºC. THIS MAY DAMAGE THE EQUIPMENT.
Technical Drawing:
Components
USB Cable 120cm*1 Pcs,
VGA Cable 180cm*1 Pcs,
Power Cord with Switching Adapter *1 Pcs,
1.3 OSD Control
1.3.1OSD buttons
1.3.2 Adjusting with OSD control
Five different keys are well-defined for operation . They are labeled on the keypad.
-
[Power]
Key is designated for Power On/Off
-
[Menu]
Key is designated for Menu/Enter function depending on the selected item. Pressing [Menu] can invoke OSD menu. After that, [Menu] is also an entry key.
-
[+]
key is designated for selection function in up direction in OSD menu and also to increase the value on selected function,Directly use + Key is to increase brightness.
-
[-]
key is designated for selection function in down direction in OSD menu and also to decrease the value on selected function,Directly use - Key is to decrease brightness.
-
[AUTO]
key is designated for invoking AUTO ADJUST function at any time once is pressed for H-position, V-position, Pixel Clock and Phase for an optimal image.
1.4 Setup the driver
-
Plug and play USB port under win 7 win 8 win 10.For Android and Linux need using driver pls contact the sales for support.
1.5 Warranty
1 Year Free Warranty for Monitor and all components.
Our Factory
•
Dongguan CJTouch Electronic Co., Ltd
, located in Dongguan, the city famous with
its advanced manufacturing, was built on 2009.
•
It
'
s a high-tech enterprise mainly specialized in researching, manufacturing,
selling and repairing SAW,IR and touch whole products and in providing touch
solutions.
•
Products : SAW and IR touch screen and touch monitor, all in one PC and touch
kiosk.
•
Products to be used in : Gaming & gambling, POS, Medical equipment, Kiosk field
and etc .
•
Accept OEM/ODM business.
•
Producing Capacity : 150 Thousand sets / year
What We Offer:
Through our consistent and high quality performance, CJTouch has got ISO 9001 certified and has earned CE, UL, FCC, RoHS and other international certifications.
Single & Multi-touch screens (custom sizes available)
Single & Multi-touch monitors (custom sizes and functions available)
All-in-one computers
ODM/OEM services
-
SAW ( Surface Acoustic Wave) Touch Screen
-
SAW ( Surface Acoustic Wave) Touch Monitor
-
IR ( Infrared) Touch Screen
-
IR ( Infrared) Touch Monitor
-
All in one touch PC
-
Interactive Kiosk
Application field
Gaming / casino / ATM Kiosk / Hotle / KTV / TV
Industrial / Public inquiry / Coffee / Bar
Entertainment / Hospital / Restaruant / Advertising
Transport and Ticketing / Banking
Hospitality / Meeting / Teaching
Customizsed Solutions